Forum Replies Created

Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • May 15, 2019 at 11:34 pm in reply to: EHX 95000 EXT Clock #125229
    Annette_Brosin
    Participant

    See below

    March 24, 2019 at 5:11 pm in reply to: Connecting two EHX9500 looping stations w/ MIDI to go from looping 6-tracks to 12-tracks? #125002
    Annette_Brosin
    Participant

    Midi cables don’t transmit audio signals, so yes you’d need extra cables. You can either go from the outs of your first looper into the second looper, or have a mixer with 2 or 4 outs (for stereo) to go into the loopers. A mixer at the end might be a good idea simply to get a 2 track stereo for your amp/speakers.

    March 18, 2019 at 5:30 am in reply to: 45000 Midi sync to Disaster Area BPM only, no start command #124967
    Annette_Brosin
    Participant

    These SYSEX transport messages are MMC messages (Midi Machine Control), to start, stop, pause, record etc. These are different messages than program change or control change.

    This might help:

    https://en.wikipedia.org/wiki/MIDI_Machine_Control

    February 27, 2019 at 4:50 pm in reply to: EHX 95000 “new Loop” loud pop #124898
    Annette_Brosin
    Participant

    Yes! thank you :)
    I did send another question through a different post. Maybe you can help with this?

    Is there any way to ONLY send midi clock and not the start and stop messages when hitting record/start/stop? I’m synching to the 95000 a setup that involves sequencers and arpeggiators and the start/stop messages are preventing the setup to work as planned.

    February 26, 2019 at 9:47 pm in reply to: EHX 95000 “new Loop” loud pop #124895
    Annette_Brosin
    Participant

    Sorry, I also just realised that I will probably not want a monitor mix on a speaker with the clix when I have the L and R outputs going to a PA. All good :)

    February 26, 2019 at 9:11 pm in reply to: EHX 95000 “new Loop” loud pop #124893
    Annette_Brosin
    Participant

    Except that means I wouldn’t have clicktrack/Clix.

    February 26, 2019 at 6:11 pm in reply to: EHX 95000 “new Loop” loud pop #124889
    Annette_Brosin
    Participant

    Hi again, sorry for the delay. I tried it again, and the L and R outputs indeed do not produce the pop. In my current setup I am using the headphone out to my headphones and can hear a similar pop as before through the monitor out. For the headphones I am not worried, but in case I have an actual monitor speaker using one of those outs, the popping sound will definitely a problem, and turning down and up the volume for the clix might be tricky when holding an instrument getting ready to record. Does this sound like a problem that could be fixed with one of the next firmware updates?

    February 20, 2019 at 6:00 pm in reply to: EHX 95000 “new Loop” loud pop #124859
    Annette_Brosin
    Participant

    Hi! Thanks for the quick response! The whole signal flow is mono: I have my (active) bass plugged into the A input of a Boss AB 2 way splitter, the other input is taken by my volca fm (played through the arturia keystep via midi). The output goes into my digital delay (source audio nemesis), then into my HOF 2 and then finally into the left input of the 95000. I used only the monitor out to go into the AUX input of my bass amp (traynor small block 110) for line input. I wanted to attach a picture of the setup but can’t reduce the filesize to less than 137kb.

  • Author
    Posts
Viewing 8 posts - 1 through 8 (of 8 total)